Wireless solutions

Are you demolishing an inner wall to enlarge your living room? Are you redecorating your bedroom and the switch is now behind a wardrobe? No problem. Wireless controls are screwed, stuck or placed wherever you want, without drilling or channelling. The push buttons control lighting, ventilation and motors of garages, shutters, sun blinds and curtains. Remote control is also not an issue. The receivers are placed in the electrical cabinet, in the ceiling or in the in-wall mounting box of the push button.

What is home automation?

Wireless battery-powered switch, 1-fold, Zigbee®

This onefold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in your Niko Home Control installation or connected to a third-party Zigbee® network as a standard dimmer switch via Find&Bind pairing. Moreover, the switch can be paired with up to eight Zigbee® receivers for stand-alone use via Touchlink. It is battery-powered with a lifetime of at least five years, based on twenty short-press actuations a day. The wireless Zigbee® switch is mounted on a plastic base. The set (base + switch 552-72001) can be screwed on a wall (screws excluded) or glued to a flat surface with double-sided adhesive tape (included). If you want to install the onefold wireless battery-powered Zigbee® on a flush-mounting box, order the variant without plastic baseplate (552-72011). Combine it with a metal baseplate (552-720X0) instead. The wireless battery-powered switch can be connected wirelessly to the wireless smart hub for Niko Home Control (552-00001). This device can also be used in a bus wiring installation in combination with the wireless bridge for Niko Home Control (550-00640).

Wireless battery-powered switch, 2-fold, Zigbee®

This twofold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in your Niko Home Control installation or connected to a third-party Zigbee® network as a standard dimmer switch via Find&Bind pairing. Moreover, the switch can be paired with up to eight Zigbee® receivers for stand-alone use via Touchlink. It is battery-powered with a lifetime of at least five years, based on twenty short-press actuations a day. The wireless Zigbee® switch is mounted on a plastic base. The set (base + switch 552-72002) can be screwed on a wall (screws excluded) or glued to a flat surface with double-sided adhesive tape (included). If you want to install the twofold wireless battery-powered Zigbee® on a flush-mounting box, order the variant without plastic baseplate (552-72012). Combine it with a metal baseplate (552-720X0) instead. The wireless battery-powered switch can be connected wirelessly to the wireless smart hub for Niko Home Control (552-00001). This device can also be used in a bus wiring installation in combination with the wireless bridge for Niko Home Control (550-00640).

Wireless battery-powered switch, 4-fold, Zigbee®

This fourfold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in your Niko Home Control installation or connected to a third-party Zigbee® network as a standard dimmer switch via Find&Bind pairing. Moreover, the switch can be paired with up to eight Zigbee® receivers for stand-alone use via Touchlink. It is battery-powered with a lifetime of at least five years, based on twenty short-press actuations a day. The wireless Zigbee® switch is mounted on a plastic base. The set (base + switch 552-72004) can be screwed on a wall (screws excluded) or glued to a flat surface with double-sided adhesive tape (included). If you want to install the fourfold wireless battery-powered Zigbee® on a flush-mounting box, order the variant without plastic baseplate (552-72014). Combine it with a metal baseplate (552-720X0) instead. The wireless battery-powered switch can be connected wirelessly to the wireless smart hub for Niko Home Control (552-00001). This device can also be used in a bus wiring installation in combination with the wireless bridge for Niko Home Control (550-00640).

Niko dimmer switch, KNX®

This wireless and battery-free dimmer switch in Niko design can operate as a switch, a dimmer, a roller shutter control or a scene selector in a KNX® system. This dimmer switch works together with the KNX® wireless media coupler (360-33001) who transmits the KNX® commands to the KNX® bus. This allows you to easily extend a KNX® system without breaking walls or installing extra cables. Configure the dimmer switch buttons with the ETS software that is available on the KNX® Association website together with the KNX® programming adapter (360-39001). The following communication objects can be linked to the buttons: single channel, dimming and shutter control. The supported functions are: on, off, toggle, up, down, darker, brighter, scene number, send value in percentage, in angle, in 2 bits, in 8 bits. Up to six button combinations can be configured. The dimmer switch can be mounted into a European flush-mounting box, screwed onto a wall (screws not included) or glued to a flat surface with double-sided adhesive tape (included).

Niko dimmer switch, EnOcean®

With this wireless and battery-free dimmer switch in Niko design, you can remotely operate EnOcean® certified wireless receivers (e.g. presence detectors with EnOcean® interface). No wall breaking or cable installation is needed. The pairing procedure with a wireless receiver determines the function of each button. Up to four buttons can be configured. The dimmer switch can be mounted in a European flush-mounting box, screwed onto a wall (screws not included) or glued to a flat surface with double-sided adhesive strips (included).

Programming adapter, KNX®

This programming adapter allows you to provide the KNX® wireless and battery-free dimmer switch (360-31001) with energy during commissioning. Connect the programming adapter to the KNX® dimmer switch and configure the functions of the buttons using the ETS software that is available on the KNX® Association website. The adapter requires two AAA batteries (not included).

Wireless hand-held transmitter with 4 channels and 13 action buttons

With this hand-held transmitter, you control a maximum of 52 circuits, independent of one another, but dependent on the receiver settings. You use the hand-held transmitter for one-key, two-key and four button functions. The operation status and channel selection is indicated with LEDs. This hand-held transmitter cannot be used in Niko Home Control installations.

Wireless 2-channel transmitter with Easywave protocol

The wireless two-channel transmitter is suitable for flush mounting and may only be used to control wireless receivers. By using this two-channel transmitter, you can expand the switching function of existing switches or push buttons via a receiver. The two-channel transmitter checks whether a switch/push button is live and transmits the corresponding code (A, B, C or D) to the wireless receiver, which in turn switches the consumer. This wirelesss two-channel transmitter cannot be used in Niko Home Control installations.

Universal wireless 1-channel dimmer, single pole, for flush mounting

The universal wireless one-channel dimmer (single-pole) is suitable for flush mounting and may only be used to switch wirelessly and dim lights up to a maximum of 250 W. You can also directly connect a fixed N.O. push button to this dimmer. With a wireless push button or a hand-held transmitter (one- or two-button control) connected to the dimmer, the lighting is always gradually switched on and off and dimmed up and down. To switch or to dim the lighting locally, you can also connect a fixed N.O. push button to the dimmer. The integrated electronic short-circuit, overload and overheating protection guarantees maximum safety during use. The dimmer may not be used to switch or to dim electric motors.

Wireless 1-channel receiver, for flush mounting

The wireless Easywave receiver with 230 V two-way switching contact (one-channel) is suitable for flush mounting and may only be used as a wireless Easywave control in combination with small electrical loads. This wireless Easywave receiver can be switched in one of the following three working modes: two modes for the on-off function and pulse mode. You can operate the receiver using either wireless Easywave push buttons (410-0000X) or hand-held Easywave transmitters.

1-channel flush-mounting wireless receiver, single pole

This mini receiver equipped with a single-pole switching contact (10 A/230 Vac) is used to switch the lighting. The receiver operates both with wall transmitters and hand-held transmitters in a one- or two-button mode. Its limited dimensions make it perfectly suitable for flush mounting.

1-channel flush mounting wireless receiver, single pole, potential free

This mini receiver is provided with a single-pole, potential-free switching contact (6 A) and has a specific pulse mode for controlling a bell, dimmer, motor... Wireless transmitters can be connected to this receiver. Its limited dimensions make it perfectly suitable for flush mounting.

Wireless receiver for motor control, for flush mounting

This mini receiver with switching contact (4 A/230 Vac) is used to control roll-down shutters or venetian/vertical blinds. The receiver can be operated by both wall-mounted and hand-held transmitters in a dual-button mode for the roll-down shutter functions (open, stop and close) or in a dual-button mode for the rotation of the vertical blinds. Thanks to its limited dimensions, it is easily flush mounted.

External antenna for 05-336

The external antenna is suitable for use with all modular wireless Niko receivers and enables the reception of wireless signals in a metal electrical cabinet. The antenna is provided with a connection cable (3 m) and a connector. To be used in combination with the wireless 2-channel receiver, IP66, for surface mounting (05-336).

Plug-through socket with wireless receiver

This plug-through socket equipped with a single-pole switching contact (10 A) has three different modes: classic switching function (on/off), teleruptor and delayed off (7 min, time not adjustable).

Plug-through socket with wireless receiver and side earthing

This plug-through socket equipped with a single-pole switching contact (10 A) has three different modes: classic switching function (on/off), teleruptor and delayed off (7 min, time not adjustable). Wireless transmitters can be connected to this socket.

Wireless 2-channel receiver for motor control

This 2-channel receiver for DIN-rail mounting is controlled wirelessly via radio frequency. It has two outputs, each with two 6 A / 230 V changeover contacts and a connection for an external antenna (410-00359). You use the module to open, close or stop roll-down shutters and venetian blinds. The terrace function makes it possible to lock the closing direction of one or more outputs, thereby preventing getting locked out unintentionally.

Wireless 2-channel receiver for switchingH:HD+C612+B:I+B:I

This 2-channel receiver for DIN-rail mounting is controlled wirelessly via radio frequency. It has two, 16 A / 230 V potential-free contacts and a connection for an external antenna (410-00359). Each switch output can have 32 transmission codes linked to it. The receiver can be controlled in on/off, pulse and dead man's switch modes. The on/off mode also has two timer functions and a logic function.

Wireless window or door contact

The wireless window or door contact (transmitter) is used to control wireless receivers. The magnetic contact transmits the status of objects via wireless signals to a wireless receiver. If the window or door is opened or closed, an Easywave code is transmitted, and the connected, wireless receiver switches, depending on the set operating mode. A battery, mounting bracket with magnet, and a mounting set are included. In combination with the USB RF interface for Niko Home Control (410-00099), the wireless window or door contact can also be used in Niko Home Control installations.

Wireless 2-channel receiver, IP66, for surface mounting

The two-channel receiver for surface mounting is provided with two switching contacts (10 A/230 V) (two-way contact and single-pole contact) and two push-button inputs. The receiver can be controlled without any wiring or via local push buttons. If the receiver is used as a roll-down shutter or ventilation control, there are five specific modes for setting the roll-down shutter functions (open, stop and close) or the different ventilation speeds. When used as a motor control, both contacts are used for one motor. The receiver can only be connected to one phase. The switching contacts cannot be used for safety extra-low voltage (SELV) circuits.

Wireless 2-channel receiver, 12 – 24 Vac or Vdc, for surface mounting

The two-channel receiver for surface mounting has four operating modes. Wireless transmitters can be connected to this receiver. An external pulse push button can also be connected per channel. The receiver can only be used for switching low-voltage loads. Possible applications: two-button control (on/off functions), push-button functions (on for as long the push button is pressed), pulse function (1 s) or two-button control (roll-down shutters/venetian blinds). The roll-down shutter/venetian blind function can only be supplied with direct current (dc).

Diagnostic device

In complex or large installations, the diagnostic device (9 V block battery not supplied) helps you to determine in advance whether the wireless applications can be used or not. The device will determine the wireless signal strength in a given area and recognise all 868.3 MHz signals. Nine indication LEDs will display the reception quality of the transmission signal or the strength of the interference signals present. This way you can check if the range of the wireless transmitter is sufficient.

Protective cap for paintwork

The protective cap is always placed over a mechanism equipped with a finishing set. It is suitable for the Niko Pure, Niko Intense and Niko Original series.

External antenna for 410-0035X

External antenna for wireless applications. Connectable to modules 410-00351 and 410-00352. The external antenna has a connection which makes reception in a metal cabinet possible. The connection cable of the external antenna is 3 meters long.

This website makes use of the following types of cookies: