Wireless 1-channel receiver, for flush mounting
The wireless Easywave receiver with 230 V two-way switching contact (one-channel) is suitable for flush mounting and may only be used as a wireless Easywave control in combination with small electrical loads. This wireless Easywave receiver can be switched in one of the following three working modes: two modes for the on-off function and pulse mode. You can operate the receiver using either wireless Easywave push buttons (410-0000X) or hand-held Easywave transmitters.
Product details
Wireless Easywave receiver with 230 V two-way switching contact (one-channel)
The wireless Easywave receiver with 230 V two-way switching contact (one-channel) is suitable for flush mounting and may only be used as a wireless Easywave control in combination with small electrical loads. This wireless Easywave receiver can be switched in one of the following three working modes: two modes for the on-off function and pulse mode. You can operate the receiver using either wireless Easywave push buttons (410-0000x) or hand-held Easywave transmitters.
Specification description
Wireless Easywave receiver with 230 V two-way switching contact (one-channel)
- Not compatible with the wireless bridge, nor with the wireless smart hub
- Input voltage: 230 Vac ± 10 %, 50 Hz
- Communication protocol: Easywave
- Operating frequency: 0.8683 GHz
- Ambient temperature: -20 – +60 °C
- Protection degree: IP20
- Dimensions (HxWxD): 48 x 48 x 25 mm
- Marking: CE
Related products
Wireless battery-powered switch, 2-fold, Zigbee®
This twofold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in your Niko Home Control installation or connected to a third-party Zigbee® network as a standard dimmer switch via Find&Bind pairing. Moreover, the switch can be paired with up to eight Zigbee® receivers for stand-alone use via Touchlink. It is battery-powered with a lifetime of at least five years, based on twenty short-press actuations a day. The wireless Zigbee® switch is mounted on a plastic base. The set (base + switch 552-72002) can be screwed on a wall (screws excluded) or glued to a flat surface with double-sided adhesive tape (included). If you want to install the twofold wireless battery-powered Zigbee® on a flush-mounting box, order the variant without plastic baseplate (552-72012). Combine it with a metal baseplate (552-720X0) instead. The wireless battery-powered switch can be connected wirelessly to the wireless smart hub for Niko Home Control (552-00001). This device can also be used in a bus wiring installation in combination with the wireless bridge for Niko Home Control (550-00640).
Wireless battery-powered switch, 4-fold, Zigbee®
This fourfold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in your Niko Home Control installation or connected to a third-party Zigbee® network as a standard dimmer switch via Find&Bind pairing. Moreover, the switch can be paired with up to eight Zigbee® receivers for stand-alone use via Touchlink. It is battery-powered with a lifetime of at least five years, based on twenty short-press actuations a day. The wireless Zigbee® switch is mounted on a plastic base. The set (base + switch 552-72004) can be screwed on a wall (screws excluded) or glued to a flat surface with double-sided adhesive tape (included). If you want to install the fourfold wireless battery-powered Zigbee® on a flush-mounting box, order the variant without plastic baseplate (552-72014). Combine it with a metal baseplate (552-720X0) instead. The wireless battery-powered switch can be connected wirelessly to the wireless smart hub for Niko Home Control (552-00001). This device can also be used in a bus wiring installation in combination with the wireless bridge for Niko Home Control (550-00640).
Niko dimmer switch, KNX®
This wireless and battery-free dimmer switch in Niko design can operate as a switch, a dimmer, a roller shutter control or a scene selector in a KNX® system. This dimmer switch works together with the KNX® wireless media coupler (360-33001) who transmits the KNX® commands to the KNX® bus. This allows you to easily extend a KNX® system without breaking walls or installing extra cables. Configure the dimmer switch buttons with the ETS software that is available on the KNX® Association website together with the KNX® programming adapter (360-39001). The following communication objects can be linked to the buttons: single channel, dimming and shutter control. The supported functions are: on, off, toggle, up, down, darker, brighter, scene number, send value in percentage, in angle, in 2 bits, in 8 bits. Up to six button combinations can be configured. The dimmer switch can be mounted into a European flush-mounting box, screwed onto a wall (screws not included) or glued to a flat surface with double-sided adhesive tape (included).
