Wireless 2-channel receiver, IP66, for surface mounting
The two-channel receiver for surface mounting is provided with two switching contacts (10 A/230 V) (two-way contact and single-pole contact) and two push-button inputs. The receiver can be controlled without any wiring or via local push buttons. If the receiver is used as a roll-down shutter or ventilation control, there are five specific modes for setting the roll-down shutter functions (open, stop and close) or the different ventilation speeds. When used as a motor control, both contacts are used for one motor. The receiver can only be connected to one phase. The switching contacts cannot be used for safety extra-low voltage (SELV) circuits.
Product details
Surface-mounting RF receiver, IP66 with 2 channels
This surface-mounting receiver is protected against dust and powerful water jets (IP66). You control it wirelessly or with push buttons. It has 2 10A/ 230V switch contacts (two-way and 1-pole contacts) and 2 push-button inputs. You can choose from 5 modes for the on/off functions. These can be independently set for each output. You set the operating time to between 0 and 3 seconds and the switch-off time between 0 and 120 minutes. Do you use the 2-channel receiver for the control of roller shutters or a ventilator? Then you have the following specific function settings:
- opening, closing or stopping the roller shutters;
- setting the speed of the ventilator.
Will you use the receiver for the control of a motor? Then, the device uses both contacts for one motor. You may only use it in a 1-phase distribution network. The contact may not be used for circuits with safety extra-low voltage (SELV).
Specification description
Surface-mounting RF receiver, IP66 with 2 channels
- Not compatible with the wireless bridge, nor with the wireless smart hub
- Maximum MCB rating: 10 A (limited by national installation rules)
- Communication protocol: Easywave
- Maximum radio frequency power: -11.29 dBm
- Operating frequency: 0.8683 GHz
- Protection degree: IP66
- Weight: 645 g
- Dimensions (HxWxD): 56 x 94 x 180 mm
- Marking: CE
Related products
Niko dimmer switch for Hue system
With this wireless and battery-free dimmer switch, you can effortlessly operate Philips Hue lamps. Determine in the Philips Hue app what each button must do (switching on and off, dimming, activating scene settings). No wall breaking or cable installation is needed. The dimmer switch can be mounted on a European flush-mounting box, screwed onto a wall (screws not included) or glued to a flat surface with double-sided adhesive strips (included). Please note that Philips Hue Bridge v2 is required and not included.
Niko dimmer switch, KNX®
This wireless and battery-free dimmer switch in Niko design can operate as a switch, a dimmer, a roller shutter control or a scene selector in a KNX® system. This dimmer switch works together with the KNX® wireless media coupler (360-33001) who transmits the KNX® commands to the KNX® bus. This allows you to easily extend a KNX® system without breaking walls or installing extra cables. Configure the dimmer switch buttons with the ETS software that is available on the KNX® Association website together with the KNX® programming adapter (360-39001). The following communication objects can be linked to the buttons: single channel, dimming and shutter control. The supported functions are: on, off, toggle, up, down, darker, brighter, scene number, send value in percentage, in angle, in 2 bits, in 8 bits. Up to six button combinations can be configured. The dimmer switch can be mounted into a European flush-mounting box, screwed onto a wall (screws not included) or glued to a flat surface with double-sided adhesive tape (included).
Niko dimmer switch, EnOcean®
With this wireless and battery-free dimmer switch in Niko design, you can remotely operate EnOcean® certified wireless receivers (e.g. presence detectors with EnOcean® interface). No wall breaking or cable installation is needed. The pairing procedure with a wireless receiver determines the function of each button. Up to four buttons can be configured. The dimmer switch can be mounted in a European flush-mounting box, screwed onto a wall (screws not included) or glued to a flat surface with double-sided adhesive strips (included).
