Analogue sensor module
The analogue sensor module allows you to connect three external analogue sensors with an output of 0-10 V to the Niko Home Control installation. These sensors must be suitable for applications with a safety extra-low voltage (SELV), such as sensors for measuring sunlight, wind, rain, CO2, humidity, or temperature. In function of the values measured, applications such as sunblinds, roll-down shutters, and lights can be operated automatically.
Product details
Analogue sensor module for Niko Home Control
Up to three external analogue sensors can be connected to the Niko Home Control installation using the analogue sensor module. The sensors must be suitable for use in applications with safety extra-low voltage (SELV). This type of sensor is used for measuring sunlight, wind, rain, CO2, humidity, or temperature. In function of the values measured, applications such as sunblinds, roll-down shutters, and lights can be operated automatically.
Specification description
Analogue sensor module for Niko Home Control.
- Function: Up to three external analogue sensors can be connected to the Niko Home Control installation using the analogue sensor module. The sensors must be suitable for use in applications with safety extra-low voltage (SELV). This type of sensor is used for measuring sunlight, wind, rain, CO2, humidity, or temperature. In function of the values measured, applications such as sunblinds, roll-down shutters, and lights can be operated automatically.
When a connected sensor is activated, the corresponding input will receive a signal between 0 and 10 V and the module will forward this value and the address to the controller, which then activates one or several pre-programmed actions. Each value corresponding to a certain input voltage is set via the programming software. Activation of a connected sensor can be simulated by pressing the button. The real input will in that case be deactivated for two minutes.
The distance between the sensors and the module should not exceed 100 m. A maximum of three sensors can be connected per module. Up to 10 modules can be connected per installation.
When the module is functioning properly, the STATUS LED will light up in TEST mode only. If one or several errors occur, the LED will blink to indicate the error code of the error with the highest priority.
Suitable for sensors with an output of 0-10 V (SELV)
Maximum distance between sensors and sensor module: 100 m
- Sliding contact to connect the module to the following module on the DIN rail
- Connection terminals: 1 x 4 screw terminals
- Wire capacity
- 3 x 1.5 mm² of 2 x 2.5 mm² or 1 x 4 mm² wire per terminal
- DIN dimensions: 2U
- Dimensions (HxWxD): 90 x 35 x 66 mm
- Marking: CE
Related products
Connected controller for Niko Home Control II
The connected controller is the central module of every Niko Home Control installation for bus wiring. This module contains firmware that can only be programmed with the Niko Home Control programming software 2.1.1 or higher. It covers all basic functions on which a Niko Home Control installation is built. The basic functions include: • The intelligence directing the logic to the installation. Through the configuration software, the logic is saved locally on the controller. • The power supply module providing an input voltage of 26 V to the bus, the cabinet modules and the controls. Depending on the size of the installation, separate power supply modules can be added. • The connection to Niko Home Control IP devices such as touchscreens and external video units. A built-in router allows the user to connect up to 3 devices directly to the controller. With an extra switch, this number can be increased. • The connection to the internet. This enables the user to control the installation both indoors and outdoors (via mobile networks such as 3G, 4G, GPRS or Wi-Fi hotspot) using mobile devices (smartphones and tablets with iOS or Android). The module has a TEST button to verify the proper functioning and status of all other modules. Each installation must consist of one connected controller. After registration, your installation is connected, enabling control through the app via your smartphone and tablet, and you can enjoy the Niko services for upgrade or diagnosis of the installation.
Digital black, connected customisable control screen, 24 V
Digital black is a customisable control screen for Niko Home Control with an extremely user-friendly interface with clear symbols. The screen is automatically activated when your hand comes near. That way, you can switch or dim your lights, set scenes, set ventilation modes, and adjust blinds and sunblinds to the desired position in one operation. In short, all possible Niko Home Control control types are available. As this Digital black 24 V variant is equipped with a temperature sensor and algorithm, it can be programmed as a zone-thermostat when linked to a Niko Home Control heating cooling module (550-00150) or switching module (550-00103 or 550-00106) programmed for electrical heating. Do you have an active connection with one of our heating partners? Then you can easily set the temperature with Digital black. When Digital black is used as a thermostat, you define the set points and week programs in the Niko Home app. With the Niko Home app you can choose which controls are displayed or where they are displayed on the screen, but also the way you navigate through your control screens. You can download this app for free in the App store or the Google Play store. Digital black can be easily mounted in any standard flush-mounting box using the familiar claw or screw fixing and is powered by a separate 24 Vdc supply (e.g. 340-00050). The screen communicates via your Wi-Fi network with the rest of your Niko Home Control system. You need an active internet connection to activate Digital black. This internet connection ensures that your Digital black and Niko Home Control installation are always up-to-date and have the most recent functionalities.
Power supply
The power supply, in combination with the connected controller, provides an extra input voltage of 26 V to the bus, modules and controls. An extra power supply is only necessary in installations for which the power of the built-in power supply of the connected controller is insufficient. Up to 2 extra power supplies can be connected to installations with a connected controller. The MASTER button is not used, as the built-in power supply of the connected controller is always the master. For more information on the required number of power supplies, you can consult the installation manual.
