Socket outlet with voltage indication, pin earthing and shutters, flush-mounting depth 28.5 mm, base with plug-in terminals and finishing set white

Compound socket outlet (base and finishing set) with pin earthing. The base is equipped with plug-in terminals and claw fixing. The socket outlet also has a shutters and has a flush-mounting depth of 28.5 mm. The central plate has a transparant lens. The compound socket outlet has an amber LED that lights up when there is a voltage on the socket outlet. The amber LED can be replaced by another colour: red, green, white or blue. Finishing colour: white

Socket outlet with voltage indication, pin earthing and shutters, flush-mounting depth 28.5 mm, base with plug-in terminals and finishing set white.

• Protection degree: IP20
• Protection degree: IP41 for the combination of a mechanism, central plate and faceplate
• The combination of a mechanism, a central plate and a faceplate has an impact-resistance of IK06
• Marking: CE

Finishing set with transparent lens for socket outlet with voltage indication, pin earthing and shutters, flush-mounting depth of 28.5mm, white. This central plate is surrounded with a flat edge that is equipped at all 4 corners with a rectangular opening, each containing a multi-positional snap hook. The construction of the central plate ensures that the faceplate can always be attached flat to the wall, even in cases of untidy plasterwork. This works in two directions: If the flush-mounting box sticks out of the plasterwork, the multi-positional snap hooks can compensate for a 1 to 1.2 mm margin; if the flush-mounting box is sunk too deeply in the plasterwork, the snap hooks can compensate for up to a 1.8 mm margin. The flat edge around the central plate also has 4 round openings that ensure the correct positioning of the faceplate in relation to the central plate. After mounting all components (faceplate, finishing set and switch), no metal parts are visible thanks to the flat edge of the central plate.

• Material central plate: The central plate is made of rigid PC and ASA. The base material is coloured in mass.
• Colour: white (mass-dyed, approximately NCS S 0502 - Y50R, RAL 9010)
• Lens: The central plate is provided with an upstanding, rectangular, transparent lens (1 x 5 mm) at the bottom left for a flush-mounting socket outlet with voltage indication module.
• Dismantling: To dismount simply unscrew the central plate.
• Shutters: Equipped with shutters. This means that contact is made after simultaneous introduction of the pins of a plug but prevents contact from being made if only 1 pin is introduced or if the two pins are not introduced simultaneously.
• Protection degree: The combination of a mechanism, a central plate and a faceplate has a protection degree of IP21D
• Impact resistance: The combination of a mechanism, a central plate and a faceplate has an impact-resistance of IK06
• Fire safety
  • the plastic parts of the central plate are self-extinguishing (comply with a filament test of 650 °C)
  • the plastic parts of the central plate are halogen-free
• Dimensions of finishing with flat edge: 56 x 56 mm (HxW)

Dimensions of visible area of finishing: 45 x 45 mm (HxW)

• Dimensions (HxWxD): 55.8 x 55.8 x 25.6 mm
• Marking: CE

Lighting unit with amber LED for socket outlet with voltage indication

Seen from the front of the socket outlet, the voltage indication module is clicked into the back of the base, with the LED in the bottom-left corner. The voltage indication module is clicked onto the back of the base and in doing so is immediately connected. The voltage indication module with amber LED has a polyamide housing. The amber light is produced by an LED with very limited power consumption (0.25 W). It is shockproof and does not radiate any heat. The LED has a life span of min. 50,000 burning-hours. CE marking.

• Protection degree: The combination of a mechanism, a central plate and a faceplate has a protection degree of IP21D
• Impact resistance: The combination of a mechanism, a central plate and a faceplate has an impact-resistance of IK06
• Marking: CE

Socket outlet with voltage indication, pin earthing, shutters,and with amber LED, plug-in terminals.

• Maximum MCB rating: 16 A (1.5 mm²) / 20 A (2.5 mm²) (limited by national installation rules)
• Protection degree: The combination of a mechanism, a central plate and a faceplate has a protection degree of IP21D
• Material base
  • ureumformaldehyde (UF) with high heat resistance
  • white RAL9010 (approximately)
• Material earthing: solid brass nickel-plated pin earthing
• Flush-mounting frame
  • 1 mm-thick metal
  • galvanized on all sides after cutting, even on the cut edges
  • with 4 grooves with screw hole of 7 mm
  • with 4 screw holes (indicated by a screw symbol) with a diameter of 3 mm for mounting on panels
• Required type of flush-mounting box
  • depth: min. 40 mm (cabling space included)
  • claw/screw fixing: 60 mm
  • inner diameter box: 60 mm
  • multiple boxes centre distance horizontal: 71 mm
  • multiple boxes centre distance vertical: 71 mm
  • multiple boxes centre distance vertical: 60 mm for Belgium and France
• Fixing method
  • simple mounting in a flush-mounting box with grip surfaces
  • with claws that rotate open using screws with a combination screwhead (Pz2 or slot 1 x 5.5 mm), for mounting in a flush-mounting box with grip surfaces
  • engagement depth of claws: 23.5 mm
  • claws turn back completely when loosened
• Centre-to-centre distance
  • Simple and quick assembly of one or more mechanisms by the indication (chalk line, laser, etc.) of the centre of the flush-mounting frame
  • vertical coupling centre-to-centre distance 60 mm by sliding several bases into each other, they lock themselves automatically
  • vertical coupling centre-to-centre distance 71 mm using pre-formed lips at the bottom, by folding the lips downwards over a length of 1 mm, the bases support each other and the centre-to-centre distance is guaranteed.
  • horizontal connection of multiple bases is quick and perfect thanks to the folded-up dovetails on the left and right sides
  • extra robustness due to the folded-up edges on the outside of the base and the continuation into the inside of the base
• End border: 4 rectangular openings (7 x 2.5 mm) which, if the flush-mounting box protrudes from the plasterwork, can compensate for a margin of between 1 and 1.2 mm, so that the faceplate can still butt up perfectly against the wall
• Wire connection
  • contact buses fitted with plug-in terminals for clamping the wires
• Wire capacity
  • all connection terminals at the top side of the base
  • up to 2 x 2.5 mm² wire per terminal
• Stripping length
  • 14 mm stripping length
  • indelibly indicated at the rear side: stripping length
• Lighting element
  • the base is provided with 2 rectangular recesses for a lighting unit
  • left recess (front view): a lighting unit with wires can be clicked in
• Dimensions (HxWxD): 71 x 73 mm
• Marking: CE